Home Tubing Supplies Manuals Consulting Technical Business Search Contact Links
Service/Technical Manuals -(click)   Repair Parts & Supplies -(click)   Testing the Player Piano -(click)
Player Technicians Listing -(click)      Player Piano Makers -(click)     Player Piano Roll Makers -(click)
Service Manuals & Technical Reprints - Click Here!

Re-bushing the Connecting Rod

The two most important things to you need to do before gluing in new bushings is testing the fit until it's perfect and turning 'on' the hot glue pot.

Using the old bushing as a template for the new bushing WILL NOT WORK. The only thing the old bushing is good for is determining the density (thickness and weave) and gaging the approximate width of the replacement cloth piece.

Once you have obtained a suitable replacement piece of woven felt, you need to pre-cut a strip. I start with a piece that measures 1-1/4" X 9". Next, taper the last 1-1/2" of one end in a 'V' shape (see Figure 2). Now pull the tapered end through the bearing hole. If the fit is correct, the two outside edges of the cloth will meet as the tapered end passes completely through the hole. If the total width of the cloth is too great, the edges will overlap and start to buckle. Too narrow and the edges won't meet firmly. Once you believe you've got it right, and with the cloth still in the hole, take the cam shaft and push one end into the hole. Examine the fit very carefully. There must not be ANY open space between the two edges of the bushing.

Now you're ready to glue the bushings in place. Pass the tapered end of the strip through the bearing hole and pull it along the strip until you come to within 1/2" from the end of the strip. Apply hot hide glue to the remaining 1/2" of exposed cloth and then pull that section into the bearing hole until just 1/8" of the cloth is exposed. Cut off the excess on the side opposite the glued side, leaving about 1/4" extra cloth. Immediately insert one of the ends of the cam into the newly bushed hole on the non-glued side and allow the glue to set. Then remove the rod and rough trim the strip to within about 1/8" of the bearing hole. Cut the cloth in a circular motion around the bearing as opposed to just cutting the cloth all at once. This reduces the possibility of pulling the freshly glued felt away from the wood.

Repeat the procedure for the four remaining bearings. Normally, there is plenty of room on both ends of the cam to accommodate all five connecting rods (three on the end of the cam where the gear is attached and two on the other end).

Allow the glue to set for about 30 minutes. Remove the rods from the cam. Take a new single-edged razor blade or extremely sharp exacto knife, locate the point opposite the point where the edges of the cloth join, and gently 'saw' the excess off. If you allow the glue to harden, trimming off the excess cloth will be a little more difficult and it will dull the blade more rapidly. If the glue starts sticking to the blade, allow the piece to set for a little longer. Also, be sure to clean off the blade with a little hot water after each piece is trimmed off. This will make the job go smoother.

Once the excess is trimmed off, place the rods back onto the cam ends and allow the glue to harden. I usually leave them sit overnight.

Figure 2

Refer back to 'Removing the Connecting Rods'.

Back to 'The 360-Test'.

This page was last revised on January 28, 2015 by John A. Tuttle ( John A Tuttle).

Although I prefer that you send E-Mail, if you have a non-order related question, you can reach me at (732)-840-8787.
If I'm in the Shop or at Home, I will answer the phone.
Otherwise, please leave a message.

As per the Fair Credit Billing Act, your bank cannot hold you liable for more than $50.00 of fraudulent credit card charges. PLAYER-CARE will pay the $50.00 if the unauthorized use of your card resulted from a purchase made through our site. We are so confident of the security measures we've put in place, we'll also pay you an additional $25 just for the inconvenience!

Disclaimer: Player-Care assumes no liability with regards to the suitability of any product sold at this web site. In other words, how you use the product is up to you. Player-Care is only liable for the quality of the material, and any product that is found to be defective will gladly be replaced.

Grand 16 IconGrand 32 Icon

407 19th Ave, Brick, NJ, 08724
Phone Number 732-840-8787
Upright 32 IconUpright 16 Icon
Google Adsense Ad
Free Sitemap Generator